$7.99 Flat Rate Shipping
  • 1-800-681-2739
Set Descending Direction

Grid Grid 


Page  of 1
Mark's Keg Washer

Mark's Keg Washer

$99.99

This keg and carboy washer will make clean-up a breeze. The base is designed to accommodate common homebrewing equipment while a submersible pump sprays cleaning solution down the sides of the vessel.* Designed by homebrewers for homebrewers.* Sanitizes or cleans kegs, carboys, buckets - greatly reduces…

Brewery Essentials Carboy Washer

Brewery Essentials Carboy Washer

$119.99

…instead of 5 or 6? The Brewery Essentials Carboy Wash kit makes this a reality - works with both glass and plastic carboys, powered by Mark’s Keg Washer (don’t let the name fool you - it works for carboys, too!) and using the awesome no-rinse action of Saniclean, the janitorial part of brewing…

1/4 Pint Clamp On Pullman Handpump Unit

1/4 Pint Clamp On Pullman Handpump Unit

$499.99

…installation. Comes with Engine Cylinder Nut, Engine Cylinder Tail Barb, compression washer, and drip tray. Needed to serve from a cask but not included are: a cask tap, cask plastic nut (k312), plastic tail (k313), cask sealing washer (k310), and 1/2" tubing. Optional sparkler (K307) is not included. The cooling…

Ale Extractor complete, single outlet, Bent 3/4

Ale Extractor complete, single outlet, Bent 3/4

$174.99

…the uptake of sediment. Tube is approximately 35" tall. Single outlet is 3/4" BSP thread, use with a 3/4" BSP nut (K312), tail (K313), and sealing washer (K310).

Brass Draft Tower

Brass Draft Tower

$159.99

…easy to clean and easy to use, for a perfect pour even after a few brews. Includes 5 ft of 3/16” beer line attached with tailpiece, hex nut, and washers for quick, simple installation.

Draft Box, 2 faucets

Draft Box, 2 faucets

$299.99

Insulated draft box with two faucets, two-circuit cold plate, and fittings - you supply gas system, couplers or disconnects to fit your kegs, connections for two beer shanks, and ice. The 10" x 15" cold plate is made of several pounds of aluminum, which has excellent thermal properties. The large mass…

Black Neoprene Beer Shank Washer

Black Neoprene Beer Shank Washer

$0.49

Required wherever you use a tail piece.

Double Body CO2 Regulator

Double Body CO2 Regulator

$149.99

…different pressure levels in two kegs - dispense one keg at 5 PSI and force carbonate another at 30 PSI at the same time. Contains a 0-2000 PSI cylinder gauge, two 0-60 PSI keg gauges, two check valves, two safety relief valves, and a reusable nylon cylinder washer. Gas outlets are 1/4" MFL, which fit…

Dual Gauge CO2 Regulator

Dual Gauge CO2 Regulator

$79.99

…the gas line, which allows you to instantly turn off the pressure to your kegs without beer backing up into the gas line. Use a gas connector kit (KX03-KX04) to connect a soda keg. Includes a reusable nylon cylinder washer.

Becker Disconnect Cap Washer

Becker Disconnect Cap Washer

$0.49

Cap washer for Becker brand ball lock disconnects; Becker disconnects have a flat cap.

CO2 Distributor 4-Way w/ 1/4" MFL shutoffs

CO2 Distributor 4-Way w/ 1/4" MFL shutoffs

$59.99

…to multiple kegs with one regulator. Corrosion-resistant nickel-plated brass manifold has 1/4" MFL shut-off valves with an integral check valve to prevent backflow of gas or liquid. Requires barbed swivel nuts (#K123 or K163) to connect hoses. We recommend using a flared nylon washer (#K127) and/or…

Commercial Kegerator to Homebrew Conversion Kit

Commercial Kegerator to Homebrew Conversion Kit

$0.00

…be attached to either the Sankey tap or the 1/4" mfl Ball Lock Disconnects; make sure to use the nylon washers for the best connection. If your Sankey tap does not have a beer shank nut and washer for the liquid side (some new ones don't) you'll need to add one of each. This kit may not work on all Low…

ABT Thru-Wall Bulkhead

ABT Thru-Wall Bulkhead

$39.99

Stainless compression fitting and washers to connect an ABT false bottom w/ elbow (#7524) with a 3/8" FPT ball valve (#P028 or #P061) in a Sanke keg. Drill a 11/16" hole in the wall of the keg to install.

Single Cask Tap, 3/4 BSP

Single Cask Tap, 3/4 BSP

$26.99

…plastic design ensures a solid tap once in place. Has a single output for use with a beer engine. Connect using a tail (K313), nut (K312), sealing washer (K310). Intended for use with 1/2" tubing (7106).

CO2 Distributor 3-Way w/ 1/4" MFL shutoffs

CO2 Distributor 3-Way w/ 1/4" MFL shutoffs

$44.99

…to multiple kegs with one regulator. Corrosion-resistant nickel-plated brass manifold has 1/4" MFL shut-off valves with an integral check valve to prevent backflow of gas or liquid. Requires barbed swivel nuts (#K123 or K163) to connect hoses. We recommend using a flared nylon washer (#K127) and/or…

Stainless Steel Draft Tower

Stainless Steel Draft Tower

$179.99

…easy to clean and easy to use, for a perfect pour even after a few brews. Includes 5 ft of 3/16” beer line attached with tailpiece, hex nut, and washers for quick, simple installation.

Double Cask Tap, 3/4 BSP

Double Cask Tap, 3/4 BSP

$36.99

…ensures a solid tap once in place. Has double output for use with two beer engines. Connect each output using a tail (K313), nut (K312), sealing washer (K310). Intended for use with 1/2" tubing (7106).

Hop Filter, 3/4 BSP

Hop Filter, 3/4 BSP

$0.90

Use with dry-hopped casks to filter out hop particles. Installed between cask tap and tail piece. Includes built in sealing washer.

Chrome Draft Tower

Chrome Draft Tower

$99.99

…easy to clean and easy to use, for a perfect pour even after a few brews. Includes 5 ft of 3/16” beer line attached with tailpiece, hex nut, and washers for quick, simple installation.

Sankey Coupler - All-stainless

Sankey Coupler - All-stainless

$49.99

…Sankey coupler, fits almost all North American beer kegs: Bud, Michelob, Busch, Miller, Coors, Killians, Sam Adams, Pete's, Molson, Labatt, OV, Moosehead, Summit, Bells, etc.Needed but not included are a tail piece, beer nut, and black beer shank washer which can be found on our Shanks & Tail Pieces page…

CO2 Distributor 8-Way w/ 1/4" MFL shutoffs

CO2 Distributor 8-Way w/ 1/4" MFL shutoffs

$99.99

…to multiple kegs with one regulator. Corrosion-resistant nickel-plated brass manifold has 1/4" MFL shut-off valves with an integral check valve to prevent backflow of gas or liquid. Requires barbed swivel nuts (#K123 or K163) to connect hoses. We recommend using a flared nylon washer (#K127) and/or…

Brewery Essentials 2 Clean Kit

Brewery Essentials 2 Clean Kit

$34.99

…handy beaker for dosing out liquid sanitizers and a faucet-mounted bottle washer (also works for carboys!) that will save you time, labor, and gunky bottles. Includes:* 1 lb. PBW* 16 oz. Star San* Jet Bottle Washer - the washer uses a 3/4" FGH connection, you may need an adapter (#7233) to connect it…

US Sankey Coupler

US Sankey Coupler

$36.99

…and Canada, fits almost all North American beer kegs: Bud, Michelob, Busch, Miller, Coors, Killians, Sam Adams, Pete's, Molson, Labatt, OV, Moosehead, Summit, Bells, etc.Needed but not included are a tail piece, beer nut, and black beer shank washer which can be found on our Shanks & Tail Pieces page…

Nylon Washer for CO2 Regulators

Nylon Washer for CO2 Regulators

$0.49

Replacement washer fits between our regulator and the CO2 cylinder. Reusable.

Sealing Washer, Nitrile Food Grade, 3/4 BSP

Sealing Washer, Nitrile Food Grade, 3/4 BSP

$0.49

Used with a 3/4 BSP tail (K313) and nut (K312) connected to a cask tap.

Flared Washer for Cold Plate Fittings

Flared Washer for Cold Plate Fittings

$0.49

Flared washer for barbed cold plate fittings (#K228 and K229).

Guinness Coupler

Guinness Coupler

$80.99

Fits Guinness, Harp and Kilkenny kegs.Needed but not included are a tail piece, beer nut, and black beer shank washer which can be found on our Shanks & Tail Pieces page.

European Sankey Coupler

European Sankey Coupler

$38.99

Fits kegs from Heineken, Amstel, Murphy's, Scottish & Newcastle beers (McEwans, Newcastle), Pilsner Urquell. Needed but not included are a tail piece, beer nut, and black beer shank washer which can be found on our Shanks & Tail Pieces page.

German "A" Coupler

German "A" Coupler

$99.99

Fits most German beer kegs: Warsteiner, Hacker-Pschorr, Spaten and Paulaner.Needed but not included are a tail piece, beer nut, and black beer shank washer which can be found on our Shanks & Tail Pieces page.

Bass Coupler

Bass Coupler

$82.99

Fits Bass, Watneys and Anchor Brewing kegs.Needed but not included are a tail piece, beer nut, and black beer shank washer which can be found on our Shanks & Tail Pieces page.

Compression Washers

Compression Washers

$0.49

Leather replacement washer for Pullman beer engines. Used between the tail piece (K313) and the beer engine. Also used below the tap handle (K326).

Plastic Nut, 3/4 BSP

Plastic Nut, 3/4 BSP

$1.99

Nut to be used with a sealing washer (K310) and tail (K313). Connects to a cask tap with a 3/4 British Standard Pipe (BSP) thread size.

CO2 Distributor 6-Way w/ 1/4" MFL shutoffs

CO2 Distributor 6-Way w/ 1/4" MFL shutoffs

$88.99

…to multiple kegs with one regulator. Corrosion-resistant nickel-plated brass manifold has 1/4" MFL shut-off valves with an integral check valve to prevent backflow of gas or liquid. Requires barbed swivel nuts (#K123 or K163) to connect hoses. We recommend using a flared nylon washer (#K127) and/or…

Beer Shank - Chrome Plated 3" x 3/16" bore

Beer Shank - Chrome Plated 3" x 3/16" bore

$14.99

…chrome-plated shank. Install through a wall or refrigerator door to mount a faucet. Requires a beer faucet on one end, and a wing nut, tail piece, and washer on the other. Approximately 2.25" of thread.

Economy CO2 Regulator

Economy CO2 Regulator

$49.99

Economy regulator without a high-pressure gauge or a shutoff/check valve. All ports are right hand thread. Includes a reusable nylon cylinder washer.

Beer Shank Hex Nut

Beer Shank Hex Nut

$1.29

Attaches tail piece to a shank. Use a neoprene washer (#K030) to seal.

Beer Shank - Chrome Plated 5.125"  3/16" bore

Beer Shank - Chrome Plated 5.125" 3/16" bore

$19.99

…chrome-plated shank. Install through a wall or refrigerator door to mount a faucet. Requires a beer faucet on one end, and a wing nut, tail piece, and washer on the other. Approximately 4.25" of thread.

Beer Shank Wing Nut

Beer Shank Wing Nut

$4.49

Attaches tail piece to a shank. Use a neoprene washer (#K030) to seal.

Plastic Tail, 1/2 x 3/4 BSP

Plastic Tail, 1/2 x 3/4 BSP

$1.99

Tail connector to be used with a sealing washer (K310) and nut (K312). Connects to a cask tap with a 3/4 British Standard Pipe (BSP) thread size. 1/2" barb.

Beer Shank - Chrome Plated 4.125" 3/16" bore

Beer Shank - Chrome Plated 4.125" 3/16" bore

$16.99

…chrome-plated shank. Install through a wall or refrigerator door to mount a faucet. Requires a beer faucet on one end, and a wing nut, tail piece, and washer on the other. Approximately 3" of thread.

Beer Shank - Stainless 4"

Beer Shank - Stainless 4"

$24.99

…stainless shank. Install through a wall or refrigerator door to mount a faucet. Requires a beer faucet on one end, and a wing nut, tail piece, and washer on the other. Approximately 3.25" of thread.

Beer Shank - Stainless 6"

Beer Shank - Stainless 6"

$31.99

…stainless shank. Install through a wall or refrigerator door to mount a faucet. Requires a beer faucet on one end, and a wing nut, tail piece, and washer on the other. Approximately 5.25" of thread.

Cold Plate Fitting, Out

Cold Plate Fitting, Out

$2.99

Stainless liquid-out fitting for cold plates. Threaded on one end, 1/4" barb on the other. Requires flared washer (#K250).

Cold Plate Fitting, In

Cold Plate Fitting, In

$2.99

Stainless liquid-in fitting for cold plates. Threaded on one end, 5/16" barb on the other. Requires flared washer (#K250).

Beer Shank - 3" Pass-Through for Draft Boxes

Beer Shank - 3" Pass-Through for Draft Boxes

$19.99

…expand a draft box. 3/8" bore with standard beer threading, which is compatible with our K018 Hex Nut or K087 Wing Nut. You will also need a coupling washer for each shank.

Beer Shank - 4" Pass-Through for Draft Boxes

Beer Shank - 4" Pass-Through for Draft Boxes

$24.99

…expand a draft box. 3/8" bore with standard beer threading, which is compatible with our K018 Hex Nut or K087 Wing Nut. You will also need a coupling washer for each shank.